女虐女变态耻辱调教小说_欧美aa一级片_青青草原国产在线观看_美女洗澡无遮挡物无内衣内裤

歡迎來到匠仁醫療設備有限公司網站!

更多 > 新聞資訊
公司新聞
行業知識
檢測答疑
圖標 首頁 >> 新聞資訊 > 公司新聞

公司新聞

工業內窺鏡攝像機選擇鏡頭的技術依據

來源:http://yuxiaous.cn/ 發布時間:2021-08-30 瀏覽量:0

1、鏡頭的成像尺寸應與工業內窺鏡攝像機CCD靶面尺寸相一致,如前所述,有1英寸、2/3英寸、1/2英寸、1/3英寸、1/4英寸、1/5英寸等規格。
1. The imaging size of the lens shall be consistent with the size of the CCD target surface of the industrial endoscope camera. As mentioned above, it has specifications of 1 inch, 2 / 3 inch, 1 / 2 inch, 1 / 3 inch, 1 / 4 inch, 1 / 5 inch, etc.
2、鏡頭的分辨率描述鏡頭成像質量的內在指標是鏡頭的光學傳遞函數與畸變,但對擁護而言,需要了解的僅僅是鏡頭的空間分辨率,以每毫米能夠分辨的黑白條紋數為計量單位,計算公式為:鏡頭分辨率N=180/畫幅格式的高度。由于工業內窺鏡攝像機CCD靶面大小已經標準化,如1/2英寸攝象機,其靶面為寬6.4mm*高4.8mm,1/3英寸攝象機為寬4.8mm*高3.6mm。因此對1/2英寸格式的CCD靶面,鏡頭的低分辨率應為38對線/mm,對1/3英寸格式攝象機,鏡頭的分辨率應大于50對線,攝象機的靶面越小,對鏡頭的分辨率越高。
2. The resolution of the lens is the internal index describing the imaging quality of the lens, which is the optical transfer function and distortion of the lens. However, for supporters, what needs to be understood is only the spatial resolution of the lens. Taking the number of black-and-white stripes that can be distinguished per millimeter as the measurement unit, the calculation formula is: lens resolution n = 180 / height of frame format. As the size of CCD target surface of industrial endoscope camera has been standardized, such as 1 / 2-inch camera, its target surface is 6.4mm wide * 4.8mm high, and 1 / 3-inch camera is 4.8mm wide * 3.6mm high. Therefore, for 1 / 2 inch format CCD target, the low resolution of the lens should be 38 pairs of lines / mm. For 1 / 3 inch format camera, the resolution of the lens should be greater than 50 pairs of lines. The smaller the target surface of the camera, the higher the resolution of the lens.
3、鏡頭焦距與視野角度首先根據工業內窺鏡攝象機到被監控目標的距離,選擇鏡頭的焦距,鏡頭焦距f確定后,則由攝象機靶面決定了視野。
3. Lens focal length and field of view angle firstly, the focal length of the lens is selected according to the distance from the industrial endoscope camera to the monitored target. After the lens focal length f is determined, the field of view is determined by the target surface of the camera.
4、光圈或通光量鏡頭的通光量以鏡頭的焦距和通光孔徑的比值來衡量,以F為標記,每個鏡頭上均標有其大的F值,通光量與F值的平方成反比關系,F值越小,則光圈越大。所以應根據被監控部分的光線變化程度來選擇用手動光圈還是用自動光圈鏡頭。
4. Aperture or luminous flux the luminous flux of a lens is measured by the ratio of the focal length of the lens to the luminous aperture, marked with F. each lens is marked with its large F value. The luminous flux is inversely proportional to the square of the F value. The smaller the F value, the larger the aperture. Therefore, manual aperture or automatic aperture lens should be selected according to the light change degree of the monitored part.
s
新聞資訊
聯系我們
  • 公司公司:匠仁醫療設備有限公司
  • 匠仁醫療山東濟南維修部
  • 聯系人:樊經理
  • 電話:13153199508
  • 地址:山東省濟南市槐蔭區美里東路3000號德邁國際信息產業園6號樓101-2室
  • 匠仁醫療湖南長沙維修部
  • 聯系人:李經理
  • 電話:13873135765
  • 地址:湖南省長沙市雨花區勞動東路820號恒大綠洲14棟2409室
新聞資訊

樊經理:13153199508     李經理:13873135765

公司地址:山東省濟南市槐蔭區美里東路3000號德邁國際信息產業園6號樓101-2室  湖南省長沙市雨花區勞動東路820號恒大綠洲14棟2409室

     

魯公網安備 37010402441281號